1529 Continuous Polisher CP Optical Lapping Company 48" Under Construction New
Specifications: 48" Continuous Pitch or Pad Polisher under construction. Machine will incorporate a steel table, 18-22", Granite Bruiser for pitch polisher, , SS slurry pan, HD speed reducing gearbox, HD DC speed controlled workstation gearmotors, and a 3 HP DC speed controlled table drive motor. Machine will accommodate 2ea. 18" work station rings which will be included in the final price. Machine is Powder Coated, with upper assembly construction of tubular steel which is Blanchard ground and Nickel plated. Bruiser is gearmotor/lead screw positionable. Workstation positioning are the same, but are hand crank operated. Granite table can be requested by buyer.

1736 Diamond Lapping Machine Lapmaster DS-20   Good
Specifications: Multi-station Diamond Lapping Machine. SN-DLPS058. Two 20" diameter Stations. 120V, single phase.

1737 Dicing Saw MTI NSX-250 1998 Good
Specifications: Vairous blades included. SN# 2503, pn-90-06000-00, 208/40015/30amp/3ph.

1680 Double Sided Lapper Dallons 12 x 5 unkn Good
Specifications: Model 12 x 5, S/N 12-567, 12" top & bottom, stainless steel plates. Inner & outer gears are stainless. Will hold 5 - 4 1/4" Carriers with 3 1/2" part circle. Variable speed, Timer, 110 V , 1PH.

1679 Double Sided Lapper Dallons PL 12 x 5 unkn Good
Specifications: 12" Plates, Gears and top plate are stainless steel, Bottom plate is cast iron. SN# 14-435-RF. Will hold 5-4 1/4" carriers with 3 1/2" part circle. same as 50T Hoffman, Variable speed, Timer, Slurry pump, 110v,1ph Motor

1581 Evaporator Darly DMC 600 2002 Very Good
Specifications: Complete Thermal Evaporation System. #1202. 208 Volt 3 Phase 60 Hertz 30 Amp. VHS 250 diffusion pump, .5 GPM cooling water required. Televac MC300 Vacuum Gauge controller. Varian VGA250 High Vacuum Valve. Alcatel 2033 roughing pump. Switched dual 6Kv single transformer thermal source, Both sources adjustable height, Source height achieved with manual adjustment. Both sources have rotational material turrets for use with filament source. Easily adaptable for filaments or boats. Adjustable speed substrate rotation. Automated pumping system with integrated PLC/HMI interface. Mitsubishi FX2 PLC. Equipment is sold in “as is” condition without warranty.

1582 Evaporator Darly DMC 600 2002 Very Good
Specifications: Complete Thermal Evaporation System. #1203. 208 Volt 3 Phase 60 Hertz 30 Amp. VHS 250 diffusion pump, .5 GPM cooling water required. Televac MC300 Vacuum Gauge controller. Varian VGA250 High Vacuum Valve. Alcatel 2033 roughing pump. Switched dual 6Kv single transformer thermal source. Both sources adjustable height, Source height achieved with stepper motors through HMI interface. Both sources have rotational material turrets for use with filament source. Easily adaptable for filaments or boats. Adjustable speed substrate rotation. Automated pumping system with integrated PLC/HMI interface. Mitsubishi FX2 PLC. Equipment is sold in “as is” condition without warranty.

1605 Flatbed Recorder Cole Parmer R-80550-10 2011 Good
Specifications: Input impedance >1 M. Chart size 100- or 200-mm. Pen response 0.5 sec full-scale. Accuracy ±0.5% full-scale. No. of channels 2. Chart speed 1, 2, 5, 10, 20, 30 cm/min and cm/hr Power 115 VAC, 12 VAC, or 12-15 VDC. Dimensions 100-mm models: 6.25 in L x 6 in W x 3.25 in H. 200-mm models: 6.25 in L x 10.25 in W x 3.25 in H. Manufacturer number MDL 102. Brand Cole-Parmer

1748 Grinder Polisher Custom Over Arm   Very Good
Specifications: 54" sub Table with double eccentric over arm {random motion}. Suitable for plano and long radius optics. 59" actual swing above sub table. Spindle speed variable 0 to 13 rpm}. Spindle torque 9000 ft-lbs. The sub table has several drilled and threaded bolt patterns for clamping substrates. The over arm speeds are variable 0-18 rpm, with 0-16" stroke. The over arms will open for easy access to table. The over arms are telescopic up to 22". Max 17 1/2" from table to pin bearing housing. The pan is two piece aluminum and easily removable for cleaning. The machine is driven by three 1 1/2 hp, dc motors. 220 v 3 ph. This machine was built for Itek Optical Systems, Div Litton Inds. Contact Owner Direct: Von McCelvey, Metro Machine Tool, Phone 303-252-4427.

1675 Grit MicroGrit Abrasives Silicon Carbide Abrasive Grain   Excellent
Specifications: Selling as one lot. Four 135 kg barrels and One 20kg box of the following: 2 barrels of 320 grit, 1 barrel of 400 grit, 1 barrel of 800 grit and 1 box of 1000 grit. Each are unopened, unmolested and stretch wrapped.

1549 Hand Finisher Strasbaugh 6VA 1973 Good
Specifications: Powered Hand Surfacer, On-Off foot pedal, Speed range is selected by switching drive belt from one pulley to another. Pan size: 15" diameter recessed stainless bowl, Lap size 8" maximum. Spindle 1"-8 thread. Specs for this model: Spindle speeds High range 0-850 rpm, Low range 0-55rpm. Torque: High speed 24 in.-lb. constant, Low speed 300 in.-lb. constant. Motor 1/4 HP, 110V 1Ph, 60Hz. 36" x 24" x 48" HWL.

1772 Optical Coating Lab Equipment IVI Corp PerkinElmer Carey etc 48" Chamber Varies Excellent
Specifications: IVI 48" BOX COATER Chamber only (empty) Large amount of vacuum fittings included, 2010 Telemark Cheetah Digital E-Beam Sweep, purchased new in 2010 in as new condition. CLEANING LINE: Branson 8500 series 40kHz heated Ultrasonic tank (20x24x22 WLD), Heated deionized water spray booth/sink. Large SOLVENT DRYER w/pneumatic lift (22x22) and automatic pumps & heat. 120 Gal 125,000 BTU/hr GAS WATER HEATER. Being Sold as one lot or Individually. Prices Have Been REDUCED! Contact Owner: Phone 413-923-2234 Garrett Moynihan, Lambda Zero. Equipment is located in West Springfield, MA

1541 Pantograph adaptor Custom   New Excellent
Specifications: This pantograph adaptor will convert a standard precision spindle polishing machine into a cylinder lens grinder/polisher. It converts the spherical motion of the spindle machine to an X and Y direction for long radius concave or convex cylinder lenses eliminating the need to purchase a machine dedicated strictly for polishing cylinder lenses. Patent Pending. Tooling dimensions 10" x 12". Requires a minimum 20" diameter to rotate in a machine.

1606 Particle Counter Met One Instruments BT-637 2011 Good
Specifications: http://www.metone.com/documents/BT-637 Datasheet.pdf

1738 Pitch Pot Sta-Warm     Good
Specifications: 25 gallon capacity with agitator. 480V 3ph

1542 Spherometer Rings Custom   New Excellent
Specifications: Spherometer Rings. 11 Piece set (12.5mm, 16mm, 20mm, 25mm, 32mm, 40mm, 50mm, 63mm, 71mm, 80mm, 90mm. Supplied in a stand to protect the edges. Steel construction with a rust resistant plating. Brass thumb nuts for a firm collet type grip on the gauge. Rings have a .375 bore for a Mahr gauge with a sleeve or a dial indicator. Gauge not included.

1608 Surfacer Grinder Polisher Strasbaugh 6TR2DC 2004 Good
Specifications: 15-inch modern, efficient surfacer has all the fine features necessary for precision high speed grinding and polishing. Dimensions: Table Height 32"-40" adjustable; width: 22"; length: 24". Pan Size: 15". Suggested lab size: 0-12". Spindle Speed Options: Standard 18 to 180 rpm. Special High Speed 36 to 360 rpm. Special Low Speed 9 to 90 rpm. Fixed Speed - Opthalmic. Spindle Ends: 1"-8 thread. Quill End: 1/4". Motor: Heavy Duty 1/4 HP, 110 volt, single phase. 60 Hz. Net Weight: 180 lbs approx. Manual included.

1602 Telescope Primary Mirror   1 meter diameter    
Specifications: 1 metre diameter f/1.5 concave paraboloid (radius of curvature 3085mm). The mirror is fabricated from Astrosital, 150mm edge thickness and with a central perforation 250mm in diameter. Clear Aperture Outer Diameter 1000 mm, Inner Diameter 330 mm. Peak-valley surface error over the Clear Aperture is better than 110nm. The mirror surface is uncoated. The mirror was manufactured for a project that did not proceed and has never been used.

 

Home ] Automatic Notification ] Company Profile ] Condition Legend ] Contact Us ] Instruments ] Machines ] Materials ] Miscellaneous ] New Arrivals ] New Equipment Showcase ] Special Events ] Search ] List Your Equipment ] Wanted List ] What do you Need? ] Terms & Policies ] Legal Disclaimer ] Privacy Statement ]

Copyright 2001 JAX Equipment Registry, Inc. All rights reserved.
Designed by Great Webs R Us